化学试剂为什么要测定PH值
通常土壤成弱碱性,若农药成酸性,则在土壤中不会发生作用,降解快,被中和。农药的ph值对于农药的应用具有极大地意义。农药的ph值涉及到农药的稳定性。
pH值是化学溶剂的酸碱度值,是用来表示溶液的酸碱度,以判断溶液时酸性、中型还是碱性。用试纸测试,数值越趋向于0酸性越强,越趋向于14碱性越强,7为中性。在标准温度(25℃)和压力下,纯水的pH值为7。
在医学上,pH值是很重要的指标之一,可以当作评估疾病程度的依据。一般来说,pH值是需要进行测定的。测定pH值的方法很多,其中最常见的是用酸碱指示剂。
pH测量原理就是用来确定某种溶液的酸碱度。pH测定仪由传感器和二次表两部分组成。可配三复合或两复合电极,以满足各种使用场所。
在pH测量中,由于仪器、试剂、环境等因素的影响,每次测量的结果都会有一定程度的差异。为了获得更准确的结果,需要进行两次或多次测量,并对结果进行平均或取其最接近的值。
PH值高锰酸盐指数这些代表的意义,为什么要检测这 高锰酸盐类似于高氯酸盐,性质较稳定,有很强的氧化性,常用在分析化学的氧化还原滴定中。它与还原性物质及有机物质混合可能发生燃烧或爆炸。
工业水硬度测试中为什么要在PH=10的条件下进行滴定?
因为钙镁与EDTA的稳定常数不够大,允许的酸效应小,所以要选择pH=10的缓冲溶液。
沉淀钙、镁离子的适宜条件是pH=10,pH过高不加沉淀剂镁离子也会沉淀,pH过低钙、镁离子沉淀不完全,都会引起误差。
水的硬度是氧化钙跟氧化镁的合量,测定过程中如果PH大于10则氧化镁易被水解生成氢氧化钠从而不能与EDTA定量反应造成结果偏低。如果PH小于10,则EDTA容易被水解,从而造成结果偏高。
因为EDTA在在PH太低是会与氢离子结合,PH太高时水中的钙镁离子可能会沉淀;并且铬黑T在酸性条件下的变色不明显,在碱性条件下由红色变为蓝色,变色明显,便于观察。
暂时硬水的硬度是由碳酸氢钙与碳酸氢镁引起的,经煮沸后可被去掉,永久硬水的硬度是由硫酸钙和硫酸镁等盐类物质引起的,经煮沸后不能去掉。
为什么要用工业ph计测量锅炉水的PH值
1、有利于炉内加药处理 在进行炉内加药处理时,保持较高的炉水pH值,有利于阻垢剂与致垢物质生成分散的无定形水渣,达到较好的防垢目的。炉水pH值过高或过低都会影响加药处理效果。
2、pH值检测法 pH值是电厂工业锅炉水质中最基本的性质之一,可以通过PH试纸或PH计进行测定。其值通常在5-9之间,如果pH值过高或过低,都会对电厂工业锅炉造成不良影响。
3、维持炉水的ph主要的目的是为了阻垢,防止金属腐蚀,和防止汽水共沸现象的产生。ph的调节在锅内加药,维持在10~12是最理想的。低于着这值不能达到阻垢。高于这值刚才容易脆化,甚至穿孔,腐蚀速率很快。