photoshopcs6中滤镜下液化工具不能使用。一片黑。如图。
看看你选的图层是否正确 如果图层选择的不是纯黑的图层,请看看是不是你的图太大,内存溢出了 以前是否使用液化正常,如果是的话,建议重新启动软件,然后再选择液化。
我们在使用PS的时候,使用滤镜液化打开图片时,有时不能正常显示,只显示黑屏。这一般是设置问题,也可能是因为驱动或者兼容问题,同时有一个简单的方法解决这种问题。我们使用滤镜的液化功能打开文件时会出现黑屏。
点击“编辑”-“首选项”-“性能”。取消勾选“使用图形处理器”。点击“确定”即可。
目前的cs6液化还不能够在win7下使用(包括x32操作系统),所有装cs6的老兄都是这个样。所以老兄也不用费心了。呵呵。如果要用到液化,还是装回cs5吧(注意:cs5与cs6同时安装的话,会出现注册问题)。
电脑不心装上了恶意软件,或上网时产生了恶意程序,建议用360 卫士 、金山卫士等软件,清理垃圾,查杀恶意软件,完成后重启电脑,就可能解决。实在不行,重装,还原过系统,可以解决软件引起的问题。
有自由变换存在的情况下,或者没有选中任何图层,或图层是隐藏状态时,滤镜是无法使用的。
为什么PS里的液化功能用不了
1、画笔太大,圆圈超出了画面的范围。画笔太小,当画笔小到一定的程度,就只看到一个十字了。
2、软件版本不适配:软件版本过低或者过高,会导致液化工具无***常显示,可尝试更新或重新安装Photoshop软件来解决。
3、PS的液化工具不能用:可能 你所作用的图层, 没有像素。你的PS软件 有问题了。解决办法: 用有像素的图层。 把PS软件卸载了, 再重新下个,然后安装就可以 了。
4、这是因为ps会对rgb颜色模式的图片液化使用GPU来进行处理。有些电脑的GPU会出现不兼容的情况,导致无法液化。更换颜色模式即可解决。方法如下。
ps不能使用液化工具而且说是颜色不适合?
双击打开“PS”软件。点击“编辑”-“首选项”-“性能”。取消勾选“使用图形处理器”。点击“确定”即可。
这是因为ps会对rgb颜色模式的图片液化使用GPU来进行处理。有些电脑的GPU会出现不兼容的情况,导致无法液化。更换颜色模式即可解决。方法如下。
PS的液化功能用不了是使用错误造成的,解决方法为:打开ps导入图片,点击滤镜。接下来需要在弹出的下拉选项里点击液化。打开液化模式,在右边的界面设置画笔大小和压力。设置好就可以通过滑动来修图,如下图所示。
ps液化工具无法使用解决办法:启动软件后,选择“编辑”菜单。在“编辑”菜单下选择“首选项”,在“首选项”下,选择“性能”。在窗口中,取消“使用图形处理器”。取消勾选“使用图形处理器”,然后单击“确定”即可。
PS的液化工具不能用:可能 你所作用的图层, 没有像素。你的PS软件 有问题了。解决办法: 用有像素的图层。 把PS软件卸载了, 再重新下个,然后安装就可以 了。