荧光灯和日光灯区别
1、发光原理不同:荧光灯通过紫外线激发灯光壁上的荧光粉发光,而日光灯是依靠电流通过钨丝电阻产生的热能来发光。光源特性有别:荧光灯属于冷光源,日光灯则为热光源。节能效果:日光灯在节能方面表现更佳,荧光灯在发光过程中会产生较多热能。
2、发光原理不一样:荧光灯通过紫外线照射到灯光壁上的荧光粉发出光,日光灯是电流通过钨丝电阻,电能转化为热能时产生的光亮 光源不一样:荧光灯是冷光源,日光灯是热光源 日光灯节能,荧光灯会产生大量的热能。
3、荧光灯和日光灯在结构上存在差异。荧光灯通常指的是管形灯管,而日光灯则是指形如灯泡的直管型光源。 荧光灯的工作原理是通过电流激发荧光粉发出光,属于冷光源。而日光灯是通过电流通过气体放电,激发荧光粉发出光,同样也属于冷光源。
4、日光灯=荧光灯。区别:性质不同:白炽灯是将灯丝通电加热到白炽状态,利用热辐射发出可见光的电光源。节能灯是将荧光灯与镇流器(安定器)组合成一个整体的照明设备。 荧光灯是利用低气压的汞蒸气在通电后释放紫外线,从而使荧光粉发出可见光的原理发光。
煤气含量报警规定
1、我国对燃气报警器报警浓度的国家标准规定了以下范围:- 天燃气、液化石油气的报警浓度为1-25%LEL;- 氢气的报警浓度设定在125ppM至750ppM;- 一氧化碳的报警浓度范围设定在50至300ppM。
2、法律分析:我国燃气报警器报警浓度国家标准是:天燃气、液化石油气1-25%LEL和氢气(125ppM~750ppM)、一氧化碳50~300ppM报警设定范围。法律依据:《城镇燃气管理条例》 第十二条 县级以上地方人民应当建立健全燃气应急储备制度,组织编制燃气应急预案,取综合措施提高燃气应急保障能力。
3、理论上 长期作业的地点一氧化碳浓度要低于24PPM 也就低于30mg/m3 ,长期在有煤气区域作业 会造成慢性的煤气中毒,失眠、记忆力减退、头痛等 煤气报警仪 报警点设置为24PPM 报警 ,报警后检查报警数值,高于200PPm 建议立即离开作业现场 。
4、法律分析:我国燃气报警器报警浓度国家标准是:天燃气、液化石油气1-25%LEL和氢气(125ppM~750ppM)、一氧化碳50~300ppM报警设定范围。
化工厂为何夜晚开那么多灯
长明灯在炼厂和化工厂里的称谓不是普通意义上的灯具,而是加热炉和火炬上安装的设备,用它来保证加热炉和火炬的安全性,也是用燃气作为燃料使用的。用来保证加热炉或火炬在非正常情况下熄火时,有明火一直保持着燃烧。防止加热炉回火爆炸。
就我感觉,一天24小时,三个班,晚班是最难熬的,毕竟这有点违背人的作息规律,绝大多数的人都是白天精神,晚上犯困。所以,如果不能适应倒班生活的人,最好不要进入化工厂,因为一般的化工厂都是一天24时小时开机的,有些化工厂一年365天都正常生产,没有节日停机之说,就比如我现在就职的化工厂。
可选中1个或多个下面的关键词,搜索相关资料。也可直接点“搜索资料”搜索整个问题。
正常情况下,化工厂是连续生产的,白天和夜晚排放废气量大致相等。除非,夜晚他们调整了工艺,更换了原料。
环境污染有哪些事例?
塑料污染 塑料垃圾污染海洋环境,这是破坏环境的一个典型事例。大量的塑料垃圾被随意丢弃,最终流入海洋。这些塑料垃圾不仅威胁海洋生物的生命安全,还破坏了海洋生态系统的平衡。此外,塑料制品的制造过程也会消耗大量并排放污染物,加剧了环境压力。
莱茵河污染 1986年11月1日,瑞士桑多斯化学公司的仓库发生火灾,导致储存有1250吨剧毒农药的钢罐爆炸,有毒物质随灭火剂进入下水道,最终进入莱茵河。这场污染导致河中生物大量死亡,自来水厂关闭,与莱茵河相连的河闸也被关闭。
年6月3日,墨西哥石油公司的平台钻机打入水下3000多米深的海底油层时,突然发生严重井喷原油泄漏,污染了这一带的海洋环境。
相关事例如下:揠苗助长:有个担忧他的禾苗长不高而把禾苗往上拔的宋国人,一天下来十分疲劳但很满足,回到家对他的家人说:“可把我累坏了,我帮助禾苗长高了!”他儿子听说后急忙到地里去看苗(的情况),然而苗都枯萎了。
人类在生产和生活过程中排放的废弃物,包括工业和生活垃圾,以及医院未经处理的废弃物,严重污染了环境。 大量使用武器导致的环境污染和破坏,对生态环境造成了严重影响。 马来西亚超过8万平方公里的热带雨林因油棕种植遭到破坏,这对生物多样性构成了巨大威胁。
48年美国多诺拉 多诺拉是美国宾西法尼亚州某河谷中的小镇。1948年10月26日—30日期间,这里大部分地区受反气旋逆温控制,且26日—30日持续有雾,致使大气污染物在近地层大气中集聚。
污染有哪些?
1、八大环境污染被称为八大公害,具体如下:比利时马斯河谷烟雾。美国洛杉矶烟雾。美国多诺拉。英国伦敦烟雾。日本水俣病。日本四日市哮喘病。日本爱知县米糠油。日本富山骨痛病。切尔诺贝利核漏。
2、全国十大环境污染 四川沱江特大水污染案:2004年2至4月,四川川化股份有限公司将工业废水排入沱江干流水域,导致特大水污染事故,给成都、资阳等5市的工农业生产和人民生活造成了严重的影响和经济损失。成都市锦江区***对此案做出一审判决,相关责任人最高获刑5年,处罚金人民币4万元。
3、比利时马斯河谷烟雾:1930年12月发生在比利时马斯河谷工业区。此次污染,因为是几种有害气体与煤烟、粉尘同时对人体产生了毒害,导致了60余人死亡,数千人患病。美国多诺拉镇烟雾:1948年10月发生在美国宾夕法尼亚州多诺拉镇。
4、北美死湖 10年开始,美国和加拿大这些西半球工业最发达的地区出现了大面积的酸雨区,酸雨的酸性甚至可以与柠檬汁相比。这导致许多湖泊中的生物死亡,森林中的树木枯萎。
5、世界著名的八大环境污染是:马斯河谷烟雾 1930年12月1日至5日,时值隆冬,大雾笼罩了整个比利时大地。比利时列日市西部马斯河谷工业区上空的雾特别浓重。第三天开始,在二氧化硫(SO2)和其他几种有害气体以及粉尘污染的综合作用下,河谷工业区有上千人发生呼吸道疾病。
6、法律分析:根据污染物的性质及通常发生方式,突发性环境污染事故可分为:有毒有害物质污染事故、毒气污染事故、爆炸事故、农药污染事故、放射性污染事故、油污染事故、废水非正常排放污染事故。
可燃气体报警器检测范围是多少
设置依据如下:可燃气体报警器的测量范围为0-100%LEL,漏报按国家规定一般设置在15%lel-25%lel之间。当探测器具有下限和上限报警设置时,下限报警设置应在1%lel至25%lel的范围内,上限报警设置应为50%lel。对于只有一个报警设置的探测器,报警设置应在1%lel至25%lel的范围内。
. 可燃气体报警器的检测范围通常在0至100%LEL之间。 若检测到的气体浓度超出100%LEL的上限,报警器显示屏会闪烁并显示最高读数。 一旦气体浓度降至测量范围内,显示屏将恢复至正常显示状态。 可燃气体报警器,亦称作气体泄漏检测及报警装置,用于监测工业和家庭环境中的可燃气体泄露。
可燃气体报警器的检测范围通常设定在0至100%LEL(爆炸下限)之间。 报警器的下限默认设置为25%LEL,但可根据需要调整在5%LEL至40%LEL之间。 上限默认设置为50%LEL,并且可以从10%LEL调整至100%LEL。 报警下限的设置依据国家规定,通常在15%LEL至25%LEL之间,以避免漏报。
可燃气体报警器的测量范围通常设定在0至100%LEL(爆炸下限),这一范围确保了能够检测到从低浓度到高浓度的可燃气体。 报警器的下限默认设置为25%LEL,但这一值可以根据需要调整在5%LEL至40%LEL之间。 上限默认设置为50%LEL,但同样可以根据实际情况从10%LEL调整至100%LEL。